Skip to content
BackBoat AlmanacSign inAdd for free

Article

Chainplates: Why They Fail and How to Inspect Them

Was it useful? Tap your stars:☆☆☆☆☆

4 min read

Published By Tuna Karslı, editorHow guides are checked

Chainplates are the metal straps that connect the shrouds and stays to the hull. Every load the rig carries passes through them. They are one of the most common causes of dismasting on older boats, because they can look clean and bright on deck while corroding inside, out of sight. A little knowledge and a careful inspection go a long way.

Why they fail

Crevice corrosion

Most chainplates are made from stainless steel. Stainless relies on a thin oxide layer that needs oxygen to stay healthy. Where the chainplate passes through the deck, it is wrapped in sealant. If water gets in but oxygen cannot, the steel corrodes in the narrow gap. This crevice corrosion can eat deep pits into the metal where nobody can see it.

Fatigue

Every wave and gust flexes the rig slightly. Over decades, these cycles can start small cracks, especially at sharp corners, bolt holes and welds.

Wet bulkheads and knees

Many chainplates bolt to plywood bulkheads or knees inside the boat. Leaks around the chainplate let water soak into the wood, which rots, so the bolts lose their grip even if the metal is fine.

Signs to look for

  • Rust stains or weeping around the chainplate where it passes through the deck.
  • Cracked or lifting sealant around the chainplate cover plate.
  • Water stains, darkening or soft wood on the bulkhead or knee below.
  • Bolts with rust stains or that turn when you try them.
  • Any visible cracks, pitting or bending of the metal.
  • Gaps between the deck and the chainplate, or movement under load.

How to inspect properly

A visual check from above is not enough. A proper inspection means removing at least some chainplates:

  1. Release the rig tension on the shroud, with the mast safely supported by other shrouds or , or do it with the mast unstepped.
  2. Remove the cover plate and sealant on deck.
  3. Undo the bolts below and withdraw the chainplate.
  4. Clean it and inspect the whole length, especially the part that sat in the deck. Look for pitting, cracks and thinning. A magnifying glass helps. Dye penetrant testing can reveal fine cracks.
  5. Check the bolt holes in the bulkhead or knee, and the wood or laminate around them.

If one chainplate shows significant corrosion, inspect all of them. They were installed at the same time and have lived the same life.

When to replace

  • Any visible crack or significant pitting.
  • Original chainplates on a boat several decades old, especially if they have never been removed and inspected.
  • As part of a replacement on an older boat, when the rig is already off.

Many owners replace chainplates in a slightly heavier gauge, or in a different alloy, at the same time. A rigger or experienced yard can advise for your boat.

Re-installing

  • Seal the deck penetration so water cannot get in, and so the seal can be renewed later. Butyl tape or a good bedding compound with a properly cut slot in the deck is common.
  • Seal the deck core around the slot with epoxy so water never reaches it.
  • Use new bolts and nuts of the right grade.
  • Re-tension the rig correctly afterwards, ideally with a tension gauge.

Common questions

How often should chainplates be inspected?

Check the deck seals every season, and remove and inspect them every ten years or so, or when replacing standing rigging, earlier if there are signs of leaks or rust.

Can I inspect without removing the chainplates?

You can see the deck area and the parts below deck, but the most vulnerable section is hidden in the deck. Only removal shows its real condition.

Are bronze or titanium chainplates better?

Both are used for replacements and resist crevice corrosion better than stainless steel. They cost more. A rigger can advise what is suitable for your boat.

What does it cost to replace them?

It depends on the number of chainplates, access and whether bulkheads need repair. Ask a rigger or yard for a quote after an inspection.

Is a rust stain always a sign of a failing chainplate?

Not always. Surface staining can come from a poor-grade bolt or from other metal nearby. But it means water is reaching the steel, so investigate rather than polish it away.

Field notes

Chainplates rarely fail without warning signs; the warnings are just hidden. Check the sealant on deck every season and look at the bulkheads below. If the boat is old and the chainplates are original, plan an inspection at the next haul-out or rig work. Ask a rigger or yard for a quote, and read our guide on checks before buying.

Share

Reader ratings

No ratings yet. Was this useful? Rate it and add what you know: corrections and first-hand tips help the next reader.

★ Rate this guide
Your rating

Stars alone are fine, and so are photos alone; a few words help even more. Reviews and bay reports go live after an automatic check that turns back adverts, contact details, insults and nonsense. The business can reply in public, but cannot edit, hide or remove a review. Sent before from this e-mail? This updates your earlier rating. Your email is never shown or shared; it keeps your reviews together in your free account. By sending you confirm it is your own first-hand experience. Privacy

Suggest a correction

One correction from you helps every sailor who opens this page after you.

An editor checks every report before anything changes on the page.

Cite this page

Chainplates: Why They Fail and How to Inspect Them. Boat Almanac, updated 18 November 2026. https://boatalmanac.com/articles/chainplates-why-they-fail-and-how-to-inspect-them/ (accessed 21 November 2026).

About our data

Know something other boaters should?

What you learned the hard way can spare another crew the same lesson. An editor helps polish it.

Boat Almanac is free for every sailor and grows with what sailors add.

ShareShare on WhatsApp