Published By Tuna Karslı, editorHow guides are checked
Why paper charts still matter
GPS and electronic chartplotters are now the heart of navigation on most boats. But electronics can fail, batteries go flat and satellite signals can be lost or jammed. When that happens, a paper chart and the ability to read it are the most dependable back-up you have. Reading a chart is also the key to using a plotter properly, because the symbols on screen follow the same conventions. It is a core skill for every skipper.
Who makes nautical charts
Charts are produced by national hydrographic offices, such as the UK Hydrographic Office (ADMIRALTY) and NOAA’s Office of Coast Survey in the United States. Their work is coordinated internationally by the International Hydrographic Organization (IHO), which is why chart symbols are broadly similar around the world. Every set of symbols and abbreviations is explained in a key publication: ADMIRALTY’s Symbols and Abbreviations used on ADMIRALTY Paper Charts (NP5011) and NOAA’s U.S. Chart No. 1 are the standard references and well worth keeping aboard.
Chart types and scales
Charts are drawn at different scales for different jobs. Large-scale charts, such as 1:10,000 or 1:25,000, cover a small area in great detail and are used for harbour approaches, pilotage close to the coast and choosing an anchorage. Small-scale charts, 1:100,000 and smaller, show a large area in less detail and are used for offshore passages and overall route planning. Always use the largest-scale chart available for the area you are navigating; small-scale charts leave out hazards that could matter close inshore.
Electronic charts come in two main forms. Raster charts are scanned images of paper charts and look exactly like them. Vector charts, including official ENCs, store data in layers, so detail changes as you zoom and layers can be switched on and off. Vector charts are more flexible, but if you zoom beyond the scale at which the data was surveyed, the detail you see can be misleading.
Finding your way around a chart
- Title block: shows the chart’s name, scale, projection, the units used for depths and heights and the vertical datums.
- Latitude and longitude scales: run along the sides and the top and bottom of the chart. One minute of latitude equals one nautical mile, so always measure distance on the latitude scale at the side of the chart, level with your position, and never on the longitude scale.
- Compass rose: shows true north and, usually, the magnetic variation for a given year with its annual change. Use it to convert between true and magnetic bearings.
- Edition and corrections: charts must be kept up to date using Notices to Mariners. Check the edition date and the record of corrections before relying on a chart.
Depths and heights
Soundings show the depth of water below a reference level called . On ADMIRALTY and many other charts this is approximately Lowest Astronomical Tide (LAT), the lowest level the tide is expected to reach under average weather conditions. US charts generally use Mean Lower Low Water (MLLW). In practice there is usually more water than charted, but strong offshore winds or high atmospheric pressure can lower the sea level below chart datum, so build in a safety margin.
Heights of lights, bridges and overhead cables are measured from a different, higher reference, typically Mean High Water Springs (MHWS) on ADMIRALTY charts. Check the title block, and remember that vertical clearance under a bridge is least at high water.
Depth contours join points of equal depth and show the shape of the seabed. Contours close together near the shore mean the bottom drops away steeply; widely spaced contours mean the bottom shelves gradually.
Colours also help. Shallow water is shown in shades of blue, with the contour at which the tint stops depending on the chart. Deeper water is white. Green areas dry at low water; on ADMIRALTY charts, the height above chart datum of drying ground is shown as an underlined figure. In seas with a small tidal range, such as most of the Mediterranean, drying areas are rare, while in places such as the English Channel, Brittany or the Bay of Fundy they are extensive.
Hazard symbols
Wrecks are shown with distinct symbols depending on whether the wreck is dangerous to surface navigation, has a known least depth, or is considered safe to pass over at a given depth. Avoid anchoring near any wreck, as your anchor can easily foul it.
Rocks are shown according to whether they are always above water, cover and uncover with the tide, or are permanently submerged. A cross or an asterisk-style symbol marks rocks that are awash or underwater, and a figure next to the symbol gives the depth over the rock or the height to which it dries.
Submarine cables and pipelines are shown by distinctive lines, typically magenta on modern charts, and are often within areas where anchoring and fishing are prohibited. Anchoring there risks damaging vital infrastructure and losing your anchor.
Also look out for restricted areas, such as military exercise zones, marine reserves and traffic separation schemes, and for overfalls and tide rips, which can create dangerous seas when wind is against tide.
Buoyage: IALA regions A and B
Buoyage follows the IALA Maritime Buoyage System, which divides the world into two regions. Region A covers Europe, Africa, most of Asia, Australia and New Zealand. Region B covers North, Central and South America, Japan, South Korea and the Philippines.
Lateral marks show the sides of a channel relative to the direction of buoyage, which is generally the direction of a vessel entering harbour from seaward.
- Region A: red marks (can-shaped) are kept to port and green marks (cone-shaped) to starboard when entering harbour.
- Region B: the colours are reversed, giving the familiar American memory aid “red right returning”.
The shapes are the same in both regions; only the colours change. Always check which region you are in before a charter in a new part of the world.
Cardinal marks
Cardinal marks are the same in both regions. They are placed to the north, east, south or west of a danger and tell you to pass on the side they are named after: pass north of a north cardinal, south of a south cardinal, and so on. They are painted in black and yellow bands and carry two black cone topmarks:
| Mark | Topmark | Colours | Light (white) |
|---|---|---|---|
| North | Both cones pointing up | Black over yellow | Continuous quick or very quick flashing |
| East | Cones base to base | Black, yellow band, black | 3 flashes in a group |
| South | Both cones pointing down | Yellow over black | 6 flashes plus a long flash |
| West | Cones point to point | Yellow, black band, yellow | 9 flashes in a group |
A simple memory aid for the lights is a clock face: east at three o’clock, south at six, west at nine.
Other marks
- Isolated danger marks: black with red bands and two black spheres as a topmark, placed directly over a small danger with navigable water all round.
- Safe water marks: red and white vertical stripes with a single red sphere, marking the approach to a channel or the centre of a fairway.
- Special marks: yellow, with a yellow X topmark, marking features such as outfalls, recreation zones or data buoys.
- Emergency wreck marking buoys: blue and yellow, used to mark new dangers that are not yet charted.
Passage planning step by step
- Gather your information. Use the largest-scale charts available, a pilot book or cruising guide, tide tables and data, the list of lights and the latest weather forecast.
- Plot the route. Lay off each leg on the chart, mark waypoints and measure the distance and true course for each leg. Make sure every leg clears hazards, shallow water and busy shipping lanes by a safe margin.
- Allow for tide, current and leeway. A cross-current pushes the boat off its track, so work out the course to steer to stay on it. A plotter can do this automatically, but you should be able to do it by hand on a paper chart.
- Time your departure. In tidal waters, plan to carry a fair tide through headlands and narrows and avoid wind-against-tide conditions.
- Set clearing lines and danger limits. Note bearings or depth contours that will warn you if you stray towards a hazard.
- Identify ports of refuge. If the weather turns, the engine fails or someone is injured, where is the nearest safe shelter? Knowing the answer before you leave is part of the plan.
- Brief the crew and keep a log. Record your position, course, speed and conditions at regular intervals so you can fall back on dead reckoning if the electronics fail.
Planning a passage between harbours? Check facilities, depths and approaches in our marina guide.
Read next
Provisioning for a Long Passage: What to Stock and How to Store ItOn a long passage, food is fuel, comfort and morale. A good galley can turn a…
Best Weather Apps for Sailors Compared (Windy, PredictWind and More)Most cruising sailors now carry several weather apps on their phone, and still get caught out…
Why Is My Anchor Dragging? 7 Common CausesThere is a particular feeling when you look up and the hills have moved. A dragging…
Reader ratings
No ratings yet. Was this useful? Rate it and add what you know: corrections and first-hand tips help the next reader.
★ Rate this guide
Suggest a correction
Cite this page
How to read a nautical chart: symbols, depths and passage planning. Boat Almanac, updated 22 October 2026. https://boatalmanac.com/articles/how-to-read-a-nautical-chart/ (accessed 21 November 2026).