Skip to content
BackBoat AlmanacSign inAdd for free

Article

Anchoring guide: anchor types, sizing, technique and safety

Was it useful? Tap your stars:☆☆☆☆☆

10 min read

Published · Updated By Tuna Karslı, editorHow guides are checked

Anchoring well is one of the core skills of seamanship. A well-chosen, correctly sized and properly set anchor lets you sleep through a wind shift; a poor one leads to dragging, grounding and collisions with other boats. This guide covers anchor types and their classifications, how to size the anchor, chain and rope, how to calculate , step-by-step technique for swinging and Mediterranean mooring, the legal light and shape requirements, and the mistakes that most often end with a boat dragging at 3 a.m.

Why the whole system matters

An anchor holds a boat in position against wind, current and waves only as part of a system: the anchor, chain, rope (rode), shackles, swivel (if fitted), windlass, bow roller, and the deck fittings they load. The weakest component sets the strength of the whole. A large modern anchor on an undersized shackle, or a heavy chain led over a cracked bow roller, gives a false sense of security.

Anchor types

New-generation (roll-bar and concave fluke) anchors

Designs such as Rocna, Mantus, Ultra, Vulcan and Spade are built to turn onto their point and bury quickly. They offer high holding power for their weight and set reliably on a wide range of bottoms, which is why they have become the first choice for many cruising yachts.

Plough anchors (CQR and Delta)

The CQR (hinged shank) and the Delta (fixed shank) are well-established plough designs with decades of service. They hold well in sand and mud but are less reliable on rock, heavy weed and very hard sand. Many production boats are supplied with a Delta.

Fluke anchors (Danforth and Fortress)

Flat fluke anchors stow flat. The Fortress is an aluminium fluke design with adjustable fluke angle for soft mud. They hold very well in sand and soft mud for their weight, but are unreliable on hard ground, rock and weed, and can fail to reset if the pull reverses with the tide. They are widely used as a kedge or second anchor.

Claw anchors (Bruce type)

A one-piece claw sets quickly and copes with varied bottoms, but its holding power for its weight is lower than modern designs, so it needs to be generously sized.

Grapnel

Folding grapnels suit dinghies and short stops on rock. They are not a primary anchor for a yacht.

Type Sand Mud Weed Rock or stones Typical role
New-generation Very good Good Fair to good Fair Primary anchor
Plough (CQR, Delta) Good Good Poor to fair Fair Primary on older or production boats
Fluke (Danforth, Fortress) Very good Very good (soft) Poor Poor Kedge, second anchor, soft mud
Claw (Bruce) Fair Fair Fair Fair General purpose, size up
Grapnel Poor Poor Fair Fair Dinghy, short stops

What HHP and SHHP mean

Classification societies rate anchors by holding power relative to a standard stockless ship’s anchor of the same mass. A High Holding Power (HHP) anchor must hold at least twice as much as the standard anchor; a Super High Holding Power (SHHP) anchor must hold at least four times as much, or twice as much as an approved HHP anchor. For example, Rocna reports RINA type approval and SHHP classification for its galvanised Original models from 55 to 110 kg. These ratings are useful, but they come from tests in specific seabeds; real-world holding still depends on setting technique and scope.

Sizing the anchor, chain and rope

The anchor

Anchor size depends on length, and windage. Every manufacturer publishes a sizing table; use it as a minimum, and go up a size if the boat is heavy for its length, has a lot of windage (flybridge, high topsides, ), or you plan to anchor in exposed places. A bigger anchor costs little extra weight compared with the risk of dragging.

The chain

  • Diameter: must match both the anchor shackle and the windlass gypsy. Gypsies are made for a specific chain pitch and standard, such as DIN 766 short-link calibrated chain common in Europe, or ISO and North American high-test grades. A mismatched chain will jump or jam.
  • Grade: higher-grade (high-test) chain gives the same strength at a smaller diameter, saving weight in the bow.
  • Length: for Mediterranean cruising with anchorages of 5 to 15 metres, 50 to 70 metres of chain is common on a 10 to 14 metre yacht. A rule of thumb found in many guides is at least three times the boat’s length, but plan from the depths you will actually use and the scope you need.
  • Marking: mark the chain every 5 or 10 metres with paint or coloured inserts so you know how much is out.

Mixed chain and rope

Where weight or cost rules out all-chain, use at least a boat’s length of chain at the anchor end, then nylon rope. Nylon stretches and absorbs shock loads; polyester (Dacron) stretches far less and is a poor choice for an anchor rode. Mixed rodes need more scope than all-chain because rope has little weight to keep the pull horizontal.

The snubber

With all-chain, fit a nylon snubber (a length of stretchy rope hooked onto the chain and made fast to a bow cleat) once the anchor is set. It absorbs snatch loads, takes strain off the windlass, and quietens the chain.

Scope: how much to let out

Scope is the ratio of rode let out to the vertical distance from the bow roller to the seabed. Measure depth, add the height of the bow roller above the water, and add the rise of tide where it matters. For example, 6 metres of water plus 1 metre from waterline to bow roller is 7 metres; at 5:1 that needs 35 metres of chain.

Conditions All-chain Chain and nylon
Calm, short stop, crew aboard 3:1 to 4:1 5:1
Normal overnight 5:1 7:1
Strong wind or swell 7:1 or more 8:1 to 10:1

The figure of about 7:1 for normal conditions with rope, rising to 10:1 or more in heavy weather, is the long-standing US Coast Guard advice. In deep or crowded anchorages you cannot always reach these ratios; when scope is limited, compensate with a bigger anchor, a snubber, a second anchor or a different anchorage.

Anchoring technique step by step

  1. Choose the spot. Check the chart and pilot for depth, bottom type and shelter from the forecast wind, not the present one. Look at the swinging circle: rode length plus boat length in every direction must be clear of the shore, rocks and other boats.
  2. Prepare. Agree hand signals between bow and , check the windlass breaker is on, and take the anchor off its lashing.
  3. Approach head to wind (or head to current if it is stronger) slowly, and stop over the chosen spot.
  4. Lower, do not drop. Let the anchor reach the seabed, then pay out chain as the boat drifts back, so the chain lies in a line rather than a heap on top of the anchor.
  5. Snub gently at about three times the depth to turn the anchor over and start it digging in.
  6. Let out the full scope and make the chain fast.
  7. Set it. Motor astern gently, then progressively harder, to about half to two-thirds of cruising power. The chain should go straight and stay still; vibration or juddering means the anchor is skipping.
  8. Fit the snubber and take the load off the windlass.
  9. Check you are holding. Take two transits on fixed objects ashore, or set a GPS anchor alarm with a radius a little over your rode length. Watch closely for the first thirty minutes and after any wind shift.

Mediterranean mooring (stern-to with an anchor)

In Türkiye, Greece and many Mediterranean harbours you will drop the anchor and reverse onto a quay. Drop the anchor three to four boat lengths out, in line with your intended berth, and pay out chain steadily as you reverse; stopping the chain too early drags the anchor, and too late leaves it slack. Take stern lines ashore, then tension the chain to hold the stern off the quay. Watch for neighbours’ chains laid at an angle, and for “” ground lines in town harbours. In coves, many boats also take a stern line ashore to a rock or tree to stop them swinging.

Lights, shapes and rules

Under Rule 30 of the International Regulations for Preventing Collisions at Sea (COLREGs), a vessel at anchor shows an all-round white light (or, by day, one ball) in the fore part. A vessel under 50 metres may show a single all-round white light where it can best be seen. A vessel under 7 metres is exempt only when it is not in or near a narrow channel, fairway or anchorage, or where other vessels normally navigate. In practice, almost every yacht in a busy anchorage must show the light; a low-mounted light in the is often more visible to approaching small craft than a masthead light.

Protected seabeds

Posidonia seagrass meadows are protected in many parts of the Mediterranean, and some areas, including the Balearic Islands and parts of the French coast, restrict anchoring on them. Anchor on sand patches where you can see them. In marine protected areas and no-fishing zones, such as those in Türkiye’s Gökova Bay, check local rules or use the moorings provided.

Weighing anchor and freeing a fouled anchor

Motor gently up towards the anchor while the windlass takes in chain, so the windlass is not dragging the boat. When the chain is vertical the anchor usually breaks out; if not, make the chain fast and motor slowly ahead to break it free, then continue recovering. Wash mud off with a deck hose as it comes up.

If the anchor is fouled on a chain, cable or rock:

  • Shorten up to vertical and motor slowly in a circle around it to pull it out from a different direction.
  • If it is caught under another boat’s chain, lift the chain with the anchor, pass a rope under the other chain, take the load on the rope, lower your anchor clear, then release the rope.
  • In known foul ground, rig a tripping line from the crown of the anchor to a small buoy before you anchor, so the anchor can be pulled out backwards.
  • Never apply sustained full engine power with the chain vertical; you can damage the bow roller or the windlass.

Pre-anchoring checklist

  • Anchor shackle moused with stainless wire or a cable tie
  • Bitter end of the chain tied to a strong point with rope that can be cut in an emergency
  • Chain marked and free to run from the locker
  • Windlass breaker on; manual handle aboard
  • Snubber and chain hook ready
  • Anchor light working
  • Second anchor and rode available
  • Forecast checked for wind shifts overnight

Common mistakes

  • Too little scope: the most common cause of dragging. Assume conditions may get worse.
  • Not setting the anchor: an anchor lying on the seabed is not holding until it has been loaded astern.
  • Dropping the chain in a heap: it can foul the anchor and stop it setting.
  • Anchoring for the wind you have, not the wind forecast: a night-time shift can put a behind you.
  • Anchoring too close: boats on different rode lengths, or rope against chain, swing differently. Match your neighbours where possible.
  • Relying on the windlass to hold the boat: use a snubber or chain stopper.
  • No anchor light: it is both a legal requirement and a collision risk.

Sources

Share

Read next

Reader ratings

No ratings yet. Was this useful? Rate it and add what you know: corrections and first-hand tips help the next reader.

★ Rate this guide
Your rating

Stars alone are fine, and so are photos alone; a few words help even more. Reviews and bay reports go live after an automatic check that turns back adverts, contact details, insults and nonsense. The business can reply in public, but cannot edit, hide or remove a review. Sent before from this e-mail? This updates your earlier rating. Your email is never shown or shared; it keeps your reviews together in your free account. By sending you confirm it is your own first-hand experience. Privacy

Suggest a correction

One correction from you helps every sailor who opens this page after you.

An editor checks every report before anything changes on the page.

Cite this page

Anchoring guide: anchor types, sizing, technique and safety. Boat Almanac, updated 24 October 2026. https://boatalmanac.com/articles/anchoring-guide-anchor-types-sizing-technique-and-safety/ (accessed 21 November 2026).

About our data

Know something other boaters should?

What you learned the hard way can spare another crew the same lesson. An editor helps polish it.

Boat Almanac is free for every sailor and grows with what sailors add.

ShareShare on WhatsApp