Published By Tuna Karslı, editorHow guides are checked
Water in the that tastes of salt, a damp patch under the sink, a that leaves a white crust on its body: sooner or later every owner meets a leaking through-hull. The good news is that most leaks around these fittings are slow weeps, not floods, and a good share of them can be cured with the boat still floating. The bad news is that a through-hull is one of the few places on a boat where a careless repair can sink her. So the order of work matters more than the products you use.
First, find out exactly where the water comes from
A “leaking through-hull” can mean four different things, and each has a different fix:
- The hose joint. Water seeps where the hose meets the tail of the seacock. This is the most common case and the easiest.
- The seacock body or handle. A ball valve that weeps around the spindle, or a cone valve that needs greasing.
- Between the seacock and the through-hull. The threaded joint is loose or the thread sealant has failed.
- Between the fitting and the hull. The bedding compound under the flange has given up, or the backing pad has rotted. This is the one that usually needs a lift.
Dry everything with paper towel, then wrap a strip of toilet paper around each joint and wait an hour. The paper shows you which joint is wet. Check with the engine running too: a raw water intake can weep only when the pump pulls on it.
What you can safely do afloat
Hose joints
Close the seacock. Undo the clips, cut back the last two or three centimetres of hose if the end is hard or cracked, warm the new end in hot water and push it fully home onto the tail. Use two stainless clips with the screws turned 180 degrees from each other. If the hose has gone stiff along its length, replace it: reinforced hose is cheap and a split one below the waterline is not.
Seacock spindles and handles
Many ball valves have a gland nut under the handle. A quarter turn often stops a spindle weep. Old bronze cone valves need to be taken apart, cleaned and greased with waterproof seacock grease, and that is a job for when the boat is ashore unless you have a soft plug ready (see below) and calm water.
The seacock to through-hull thread
If the valve has loosened on its thread, do not just tighten it. Turning the valve can also turn the through-hull and break the bedding seal under the flange, turning a weep into a real leak. Hold the through-hull still from inside with a fitting tool if you have one. If the thread itself is weeping, the honest repair is ashore: undo, clean, re-seal with a proper thread sealant and re-assemble.
The emergency kit that makes afloat work safe
Before you touch anything below the waterline, have these within arm’s reach:
- A tapered softwood bung of the right size tied to each through-hull (many boats keep one tied on permanently).
- A foam emergency plug, which seals odd shapes better than wood.
- A working bilge pump and someone aboard who knows where the manual pump handle is.
- Underwater epoxy putty for a temporary outside patch.
Some owners close a fitting from outside with a diver or a snorkel and a suction plunger cup pressed over the hole. It works, buys you a few quiet minutes and is worth knowing about, but never rely on it alone.
When the leak is between fitting and hull
If the toilet paper test shows water coming from under the flange, the bedding has failed. You can buy time with an underwater epoxy fillet around the outside of the fitting, done by a diver on a clean, scrubbed surface. It is a holding repair for weeks or a season, not a cure.
Check the backing block while you are there. On older boats it is often plywood, and wet plywood turns to mush. If you can push a screwdriver into it, the fitting is no longer clamped properly and the risk is not the weep but the whole assembly loosening under load, for example when someone stands on the hose to reach a locker.
When to stop and book a lift
- Brass fittings, or bronze that has turned pink. Pink means dezincification: the metal has lost strength and can snap.
- Any crack in the through-hull or in the hull around it.
- A seacock that will not close, or will not open.
- A weep that has returned after two attempts.
Most yards can do a short lift-and-hold, often called a “lift in the slings”, so the job is done in a few hours rather than a full haul-out. Ask for it when you call. You can find yards near you on the boatyards list, or ask several for a price in one go.
Field notes
Exercise every seacock once a month. A valve that has not moved for a year is a valve that will not move when a hose bursts. Label each one with what it serves: in the dark, with water rising, “galley sink” written on the handle saves the minute you need. And when you replace a fitting, use proper marine bronze or a reinforced composite seacock system, not a garden-centre brass valve, however close it looks.
Finally, keep a note of what you did and when. A dated line in your boat’s maintenance log turns a guess into a pattern, and a buyer’s surveyor will ask.
Short version for the dock: Seacock stiff or leaking.
Reader ratings
No ratings yet. Was this useful? Rate it and add what you know: corrections and first-hand tips help the next reader.
★ Rate this guide
Suggest a correction
Cite this page
How to Fix a Leaking Through-Hull Fitting (Without Hauling Out). Boat Almanac, updated 18 November 2026. https://boatalmanac.com/articles/fix-leaking-through-hull-fitting-without-hauling-out/ (accessed 21 November 2026).