Skip to content
BackBoat AlmanacSign inAdd for free

Article

How to Change the Impeller on a Marine Engine

Was it useful? Tap your stars:☆☆☆☆☆

5 min read

Published By Tuna Karslı, editorHow guides are checked

The raw water is a small rubber wheel inside the engine’s seawater pump. It pushes seawater through the cooling system, and it is one of the most common causes of overheating. It is also cheap and, on most engines, quick to change. Every owner should change one at the dock at least once, so that doing it at sea is not the first time.

When to change it

  • Every season, or as the engine maker recommends, whichever comes first.
  • After the engine has run dry, even briefly, for example with the closed.
  • When exhaust water flow is weaker than normal.
  • When the engine has overheated and the intake and strainer are clear.

Rubber also takes a set if the engine sits for months. An impeller left in all winter may have vanes bent permanently one way.

What you need

  • The correct replacement impeller and cover gasket or O-ring for your pump model. Check the pump maker and model on its body.
  • Screwdrivers or a spanner for the cover screws, a small mirror and a torch.
  • An impeller puller, or two flat-bladed screwdrivers, or long-nose pliers.
  • Grease recommended for impellers, or a little washing-up liquid.
  • A bowl to catch the screws, which have a habit of disappearing into the .

Step by step

  1. Engine off, raw water seacock closed. Make sure nobody can start the engine while your fingers are in the pump.
  2. Remove the pump cover. Undo the screws and take off the cover and its gasket or O-ring. Some pumps are behind the alternator or in awkward places; on a few engines it is quicker to remove the whole pump, which is held by a few bolts.
  3. Remove the old impeller. Use an impeller puller if you have one. Otherwise grip the hub with long-nose pliers, or lever it out gently with two screwdrivers placed opposite each other, protecting the pump body with a rag. Do not scratch the inside of the pump housing.
  4. Inspect the old impeller. Count the vanes. If any are missing or torn, the pieces are somewhere downstream, usually at the inlet of the heat exchanger. Find them before restarting.
  5. Check the inside of the pump. Look for scoring on the cover plate and wear on the cam. A badly worn cover plate lets water slip past and reduces flow; some covers can be turned over or replaced.
  6. Prepare the new impeller. Smear a little impeller grease or washing-up liquid on the vanes and hub. This protects them during the first dry seconds before water arrives.
  7. Fit the new impeller. All the vanes must bend the same way, in the direction of rotation, which usually means the same way as the old one. A useful trick is to put a cable tie around the vanes to hold them bent, slide the impeller in and cut the tie. Line up the hub with the drive shaft’s key or flat and push it fully home, turning slightly.
  8. Refit the cover with a new gasket or O-ring, tightening screws evenly in a cross pattern.
  9. Open the seacock and start the engine. Check water flows from the exhaust within a few seconds and look for drips at the pump cover.

Common problems

  • Cannot reach the pump. A small inspection mirror and a magnetic screwdriver help. On some engines, buy a pump cover with captive quick-release screws: many owners fit one for easier future changes.
  • Impeller will not come out. Old impellers stick to the shaft. Work patiently from both sides. Do not use heat.
  • Weak flow after the change. Check the seacock is fully open, the strainer lid seals and there are no impeller pieces in the heat exchanger.

Common questions

Which way should the vanes bend?

In most pumps the vanes trail the direction of rotation. If you are not sure, note how the old impeller sat before removing it, or turn the engine by hand briefly with the cover off to see which way the shaft turns.

Is it normal for a new impeller to be tight?

Yes. New impellers are a snug fit and the vanes must be compressed to enter the housing. Grease and the cable tie trick make it much easier.

Can I use the impeller from a different pump if it fits?

Only if it is listed for your pump. Dimensions, vane count and rubber compound differ, and a near match can wear quickly or reduce flow.

Field notes

Carry at least two spare impellers and the matching gaskets. Write the date of each change on a piece of tape near the pump and in your maintenance log. If you leave the boat for a long time, some owners remove the impeller and store it in a labelled bag beside the pump, with a large note on the ignition key so the engine is not started without it. And when in doubt, or when the pump itself is leaking from the shaft seal, a marine engineer can replace the pump quickly.

Short version: Change the raw water impeller.

Share

Read next

Reader ratings

No ratings yet. Was this useful? Rate it and add what you know: corrections and first-hand tips help the next reader.

★ Rate this guide
Your rating

Stars alone are fine, and so are photos alone; a few words help even more. Reviews and bay reports go live after an automatic check that turns back adverts, contact details, insults and nonsense. The business can reply in public, but cannot edit, hide or remove a review. Sent before from this e-mail? This updates your earlier rating. Your email is never shown or shared; it keeps your reviews together in your free account. By sending you confirm it is your own first-hand experience. Privacy

Suggest a correction

One correction from you helps every sailor who opens this page after you.

An editor checks every report before anything changes on the page.

Cite this page

How to Change the Impeller on a Marine Engine. Boat Almanac, updated 18 November 2026. https://boatalmanac.com/articles/how-to-change-the-impeller-on-a-marine-engine/ (accessed 21 November 2026).

About our data

Know something other boaters should?

What you learned the hard way can spare another crew the same lesson. An editor helps polish it.

Boat Almanac is free for every sailor and grows with what sailors add.

ShareShare on WhatsApp