Published By Tuna Karslı, editorHow guides are checked
An electric pump spends most of its life doing nothing, sitting in the dirtiest, wettest corner of the boat. Then one day it is the only thing between a small leak and a big problem. If yours has stopped, runs without moving water, or the float switch sticks, replacing them is a straightforward job that most owners can do in an afternoon.
Choosing the pump
- Capacity. Pumps are rated in litres or gallons per hour at zero head, meaning with no lift and no hose. Real flow is much lower once you add a long hose, a rise to the outlet and a non-return valve. Buy more capacity than the label suggests you need.
- Voltage. Match it to your system, usually 12 V.
- Size. Measure the space in the bilge sump. The pump must sit at the lowest point and the float must have room to move.
- Outlet size. Match the hose and the through-hull. Reducing the hose diameter cuts flow sharply.
Many cruising boats carry two electric pumps: a small one low down for routine water, and a larger one mounted a little higher that only comes on when something is wrong. Plus, always, a manual pump that can be worked from the .
Choosing the float switch
Traditional hinged float switches are cheap and simple but can be jammed by debris. Enclosed float switches and electronic water-sensing switches are less likely to stick. Whatever you choose, mount it so nothing can hold it down or lift it: hoses, cables and stray objects in the bilge are the usual culprits.
Wiring it properly
This is where most bilge pump failures really come from. A good installation has:
- Power that bypasses the main battery switch. The automatic circuit should be wired so it works even when you turn the boat’s main switch off and leave. Protect it with its own fuse or breaker, sized as the pump maker says, close to the battery.
- A three-way panel switch for manual on, off and automatic, so you can test it and run it manually.
- Connections above the bilge water. Joins made down in the bilge corrode fast. If a joint must be low, use adhesive-lined heat-shrink butt connectors with tinned marine cable.
- Correct cable size for the current and the length, so voltage drop does not starve the pump.
- A light or counter on the panel that shows when the pump runs. If you see it running more often than usual, you have a leak to find.
Step by step
- Turn off the power and remove the fuse for the pump circuit.
- Remove the old pump and float switch. Note which wire went where: brown, red or marked wires to positive, black or blue to negative. Take a photo.
- Clean the sump. Dirt, hair and bits of old cable ties are what killed the last pump.
- Fit the new pump base, often with screws into a block bonded to the hull, never through the hull.
- Fit the float switch beside it, at a height that lets the pump keep the water low without running all the time.
- Connect the outlet hose with a smooth run and no sags where water can lie. Use two clips at each end.
- Make the electrical connections high and dry, as above.
- Check the outlet through-hull is well above the waterline even when heeled, or fit a vented loop so the sea cannot siphon back in.
Testing
Pour a bucket of water into the bilge and watch. The float should lift, the pump should start, water should come out of the outlet steadily, and the pump should stop when the water is low. Then test manual mode from the panel. Do this every month, and every time you return to the boat.
Common questions
How high should the float switch sit?
Low enough that the pump keeps the bilge nearly dry, high enough that it does not cycle every few minutes from a little water sloshing about. On most boats a few centimetres above the bottom of the sump works. If the pump starts often with the boat at rest, find the source of the water rather than raising the switch.
Should I fit a high-water alarm?
Yes. A separate float or sensor mounted above the normal pump level, wired to a loud buzzer and a light, tells you the pumps are not keeping up. It costs little and has saved many boats left on a mooring.
How often should I replace the pump?
There is no fixed life. Test monthly, and replace when flow drops, the motor hums without pumping, or the pump is old and corroded at the connections. Many owners carry the old working pump as a spare.
Field notes
Fit a strainer or mesh box around the pump intake and clean it often. Keep a spare pump and float switch aboard on longer trips: they are small, light and cheap compared with what they protect. And remember that an electric pump only buys you time. The real defence is knowing where every is and keeping a softwood bung tied beside each one. If you are unsure about the wiring, a marine electrician can check it in an hour.
Short version: Bilge pump not working.
Read next
Storm preparation on a boat: what to do at sea and in portWhy take storms seriously? A storm at sea is very different from one on land. Wind,…
Boat LPG system and galley safety guide: cylinder locker, regulator, gas detector and safe useLPG use in the boat galley LPG (liquefied petroleum gas) is the most common cooking fuel…
Boat fire safety guide: prevention, extinguishing equipment and emergency planFire is one of the most serious emergencies a crew can face. Ashore you can leave…
Reader ratings
No ratings yet. Was this useful? Rate it and add what you know: corrections and first-hand tips help the next reader.
★ Rate this guide
Suggest a correction
Cite this page
How to Replace a Bilge Pump and Float Switch. Boat Almanac, updated 18 November 2026. https://boatalmanac.com/articles/how-to-replace-a-bilge-pump-and-float-switch/ (accessed 21 November 2026).