Published By Tuna Karslı, editorHow guides are checked
Parts of the boat
The bow is the forward end of the boat; it parts the water as the vessel makes way. The stern is the aft end; the engine and rudder are typically located here. Port is the left side of the boat when facing forward. Starboard is the right side. At night, port carries a red light and starboard carries a green light.
The topsides are the hull surface between the waterline and the deck. The waterline (load waterline) is the line at which the hull meets the water surface. The is the main structural member running along the bottom of the hull centreline.
The deck is the horizontal surface you walk on. The is the open or semi-open working area aft where the helmsman and crew sit. The cabin is the enclosed living space below deck.
The bowsprit is a spar projecting forward from the bow; the jib or is set from it. The is the flat or slightly raked surface at the stern; motors are mounted here.
Structural terms
Frames (ribs) run upward from the keel and give the hull its shape. Deck beams run athwartships and support the deck. The is the lowest interior space of the hull; bilge water collects here and the bilge pump ejects it overboard.
Laminate (in a fibreglass boat) is the composite of glass fibre layers bonded with resin. A sandwich construction has a core material (foam or balsa) between two laminate skins; it gives lightness and stiffness.
Steering and manoeuvring
The rudder is the underwater blade that steers the boat. A is the arm used to control the rudder directly on small boats. The (wheel) is the steering wheel on larger vessels.
Hard to starboard means turning the rudder fully to the right. Hard to port means fully to the left. Let go the anchor means to drop the anchor. Weigh anchor means to retrieve the anchor.
A gybe is a change of course on a sailing boat when the wind passes from one side to the other across the stern. A tack is a change of course when the wind passes across the bow.
Mooring and rope work
A cleat is a metal or wooden fitting on the boat or dock to which lines are made fast. A bollard (bitt) is a double-headed mooring point typically found at the bow. A fairlead is a guide that leads a line through the hull or over the deck.
The bow line leads from the bow to the dock. The stern line leads from the stern. Springs are diagonal lines that prevent the boat from moving fore and aft.
Fenders are inflatable or foam buffers hung over the side to protect the boat from contact with a dock or another vessel.
Engine and machinery
Inboard means the engine is permanently mounted inside the boat. Outboard is a self-contained engine unit mounted on the transom. A sterndrive (Z-drive or I/O) has the engine inboard and a drive unit external to the hull.
The propeller (screw) converts engine power to thrust. The shaft transmits rotation from the engine to the propeller. The shaft seal (stuffing box or lip seal) prevents water entering where the shaft passes through the hull.
The impeller is the rubber-vaned rotor in the seawater cooling pump. The thermostat regulates engine temperature. The exhaust elbow mixes exhaust gas with cooling water; it is one of the most frequently replaced components due to corrosion.
Navigation
Latitude is the angular distance north or south of the equator. Longitude is the angular distance east or west of the prime meridian.
A bearing is a directional angle measured clockwise from north in degrees. A course is the direction a boat intends to go. A heading is the direction the bow actually points; current and leeway cause the heading to differ from the course made good.
A nautical mile is 1,852 metres. A knot is one nautical mile per hour. A fathom is 1.83 metres, used in depth measurement.
Read next
Marine Diesel Engine Failure at Sea: Advanced Troubleshooting, Emergency Repairs and Getting Home Under PowerAn offshore skipper's technical guide to diagnosing marine diesel failures, understanding engine systems, managing overheating, fuel…
Marina Berth Prices Compared: Turkey vs Greece vs Croatia vs SpainUpdated October 2026. Figures are drawn from published marina tariffs, owner-reported contracts and recent surveys. Always…
Wintering a yacht in Turkey: marinas, haul-out, costs, paperworkTurkey has become one of the most popular places in the Mediterranean to lay up a…
Reader ratings
No ratings yet. Was this useful? Rate it and add what you know: corrections and first-hand tips help the next reader.
★ Rate this guide
Suggest a correction
Cite this page
Marine terminology glossary: essential terms every boat owner should know. Boat Almanac, updated 22 October 2026. https://boatalmanac.com/articles/marine-terminology-glossary-essential-terms-every-boat-owner-should-know/ (accessed 21 November 2026).