Published · Updated By Tuna Karslı, editorHow guides are checked
What is a sea trial?
A is a test passage that shows how a boat and its systems behave under real operating conditions. It is normally carried out before purchase, usually alongside the pre-purchase survey, but owners also run one after a refit, an engine replacement or a change of propeller. The engine, gearbox, shaft, steering, electrics, electronics, and on a sailing yacht the rig and sails, are all observed working together. Many faults that cannot be detected at the dock only appear under load: overheating, vibration, a slipping gearbox, a weeping shaft seal or a rudder that binds at large angles.
For a buyer, the sea trial should be a formal step in the sale agreement. Most standard agreements make the purchase “subject to survey and sea trial”, which gives you the right to reject the boat or renegotiate if the trial reveals material defects. Without that clause, a trial is just a pleasant afternoon on the water.
Who should be on board
- The buyer, and ideally someone experienced with this type of boat.
- The surveyor, if the trial forms part of the survey.
- An engine technician, where the engines represent a large part of the value or are approaching major-service hours. Compression and blow-by testing is normally a separate service carried out by a technician, not part of a standard survey.
- The seller or broker, who will usually in and out of the berth. Insurance normally stays with the seller until completion, so agree in advance who is in command.
Preparation
Arrange it properly
- Ask that the engine is not run before you arrive. A cold start is one of the most revealing tests, and a pre-warmed engine hides hard starting and weak batteries.
- Agree a route that allows at least 30–60 minutes of sustained running, plus room for full-throttle runs and manoeuvring.
- Confirm fuel, water and battery charge are sufficient, and that safety equipment is on board.
- Choose suitable weather. Flat calm tells you little about handling; a light to moderate breeze and a small sea are ideal. Do not trial in strong winds: it is neither safe nor informative.
Checks at the dock before casting off
- Look in the and note the water level and whether there is oil or fuel in it. You will compare this after the trial.
- Check engine oil, coolant and gearbox oil levels, and note their colour. Milky oil suggests water or coolant contamination.
- Lay a clean absorbent pad under the engine and generator so new leaks show up afterwards.
- Record the engine and generator hour meters, so you can confirm they are working when you return.
- Check belts, hoses, hose clamps and the raw-water strainer.
- Make sure the instrument panel works: tachometer, coolant temperature, oil pressure and voltmeter. Without them you cannot record meaningful data.
- Have a notebook or a recording sheet, a camera, and if possible an infrared thermometer.
Engine test
Cold start
A healthy diesel in good adjustment should start within a few seconds of cranking once glow plugs, if fitted, have done their job. Prolonged cranking, repeated attempts, heavy smoke that persists after start, knocking or uneven running are warning signs. Check that cooling water is flowing from the exhaust outlet within seconds of starting; if it is not, stop the engine and find out why.
Running through the range
Once the engine is at operating temperature, increase revolutions in steps from idle to full throttle. At each step, typically idle, slow, half, cruising and full, record:
- engine revolutions;
- coolant temperature;
- oil pressure;
- charging voltage;
- boat speed from GPS;
- vibration and noise, and any smell.
Compare the readings with the manufacturer’s specifications in the engine manual. Most marine diesels have a specified operating temperature band and minimum oil pressures at idle and at rated speed; deviations matter more than the absolute numbers on an unfamiliar gauge, which may itself be inaccurate. An infrared thermometer pointed at the thermostat housing, exhaust elbow and heat exchanger helps confirm what the gauge says.
Wide-open throttle
The full-throttle test shows whether the engine can reach its rated maximum revolutions under load. Practical guidance is that, with the boat in normal trim and a clean bottom, the engine should reach within about 100 rpm of the manufacturer’s rated speed.
| Result at full throttle | Possible causes |
|---|---|
| Reaches rated rpm (within about 100 rpm) | Propeller correctly matched; engine delivering power |
| Well below rated rpm | Propeller too large or overpitched, fouled hull or propeller, overloaded boat, injector or fuel-supply problems, turbocharger fault, worn engine |
| Above rated rpm | Propeller too small or underpitched, slipping gearbox, damaged propeller |
| Rpm rises but speed does not | Gearbox or coupling slipping, cavitation, propeller damage |
Run at full throttle only briefly and only once the engine is warm. Watch the temperature gauge throughout; a rise at full load that falls back at cruise points to a cooling system that is marginal, often a partly blocked heat exchanger or a worn raw-water pump .
Exhaust smoke
| Smoke colour | Usual meaning |
|---|---|
| Little or none once warm | Normal for a healthy diesel |
| Black, continuous | Overfuelling or insufficient air: overloading, wrong propeller, dirty air filter, faulty injectors or turbo |
| White, persisting after warm-up | Water or coolant in the combustion chamber, or low compression; steam from wet exhaust is normal and clears |
| Blue | Oil burning: worn rings, valve guides or turbo seals |
Oil sampling
An oil sample taken from the warm engine after the trial and sent to a laboratory can reveal coolant or fuel in the oil and unusual wear metals. Results typically cost around USD 50 per sample in the US and can take about a week, so arrange the sample early in the sale timetable.
Gearbox, shaft and steering
Gear changes
Shift from ahead to neutral to astern at low revolutions, pausing in neutral. Engagement should be positive and quiet. Clunks, delay, slipping or grinding suggest gearbox, cable or coupling problems. A back-down test, moving from cruising speed through neutral into astern with sensible pauses, also shows how much the engine moves on its mounts. Excessive movement suggests worn or collapsed mounts.
Shaft seal and vibration
Inspect the shaft seal while the shaft is turning, because a seal can be dry at the dock and leak underway. A traditional packed stuffing box should drip slightly when running, about three to four drips per minute, because the water lubricates the packing. Around ten drips a minute is too much, and drips when the shaft is stopped indicate the need for adjustment or maintenance. Dripless face seals should not drip at all. Check the rudder gland at the same time.
Feel for vibration at different revolutions, including at the gearbox. Vibration or resonance at a particular speed can indicate a bent shaft, damaged or unbalanced propeller, misalignment, worn cutless bearing or failing engine mounts.
Steering and manoeuvring
- Turn to port and starboard at several speeds. Response should be prompt and smooth, without play, binding or noises.
- Carry out figure-of-eight turns at cruising speed; the turning circle should be broadly similar in both directions.
- On a straight course, briefly release the wheel or in calm water. A strong pull to one side can point to trim, rudder alignment or propeller damage. Some sheer under propeller torque is normal.
- Test astern steering. Propeller walk to one side is normal on single-screw boats; loss of control, heavy vibration or banging is not.
- On twin-engined boats, test each engine alone and practise turning on the spot. Check bow and stern thrusters if fitted, with short bursts.
- If an autopilot is fitted, engage it on a straight course and in a turn.
Electrical system and electronics
- Switch on each navigation instrument: GPS, chartplotter, radar, , , depth sounder, log and wind instruments. Check that each displays plausible data, and compare the GPS position with a known reference.
- Make a radio check on a working channel, not channel 16.
- Check the alternator is charging. A typical 12-volt system charging correctly shows around 13.8–14.4 volts at the battery while running; check the regulator or charger specification for the exact figure.
- Test navigation lights, deck lights, cabin lighting, bilge pumps and their float switches, horn, windlass and fresh-water pump.
- Look at the distribution panel. Blown fuses bridged with wire, uncapped terminals and scorched connections are fire risks.
- Run the generator under load if fitted, and test shore-power and inverter changeover.
- Confirm that carbon monoxide alarms are fitted where people sleep on boats with enclosed accommodation and engines or generators. ABYC A-24 covers the installation of carbon monoxide detectors and alarms.
Sail test (sailing yachts)
- Hoist and lower each sail. Note how easily they go up and come down and whether reefing systems work.
- Inspect sailcloth for tears, failed stitching, UV damage on furling sails and chafe at batten pockets and leech.
- Look at sail shape. A blown-out sail with the too far aft will not point well and heels the boat excessively.
- Tack a few times and gybe under control. Check that winches turn freely and their pawls engage, clutches hold, cars run on the tracks and sheets lead fairly.
- Watch the rig. Some slack in the leeward shrouds under sail is normal on many rigs; the windward shrouds should be firm, and the mast should stay in column. Excessive pumping, unexpected bend or noises from the mast step suggest a problem to investigate.
- Check that the steering stays light under sail; heavy weather helm in moderate wind points to sail trim, rig set-up or rudder issues.
General observations underway
- Look into the bilge and lockers during the trial. Is water coming in? Do any areas show fresh staining?
- Listen for creaks and bangs from bulkheads and the hull in waves, especially on planing boats.
- Smell the accommodation. Exhaust smell in the cabin suggests a leaking exhaust system: a carbon monoxide hazard and a potential fire risk. Diesel smell suggests a fuel leak; a smell of petrol or gas on a petrol or LPG-equipped boat is a reason to stop the engine and ventilate immediately.
- Check the heads, galley and hot water system if time allows.
After the trial
- Recheck the bilge, the absorbent pad and the fluid levels. Compare with your notes from before departure.
- Note the new engine hour reading.
- Feel the shaft seal and alternator for heat (carefully).
- Take oil samples if arranged.
- Write up the findings straight away while they are fresh, and share them with your surveyor.
Sea trial recording sheet
| Throttle setting | Rpm | Speed (knots) | Coolant temp | Oil pressure | Volts | Notes |
|---|---|---|---|---|---|---|
| Idle in neutral | ||||||
| Slow ahead | ||||||
| Half throttle | ||||||
| Cruising | ||||||
| Full throttle | ||||||
| Astern |
Common mistakes
- Accepting a pre-warmed engine and missing hard starting or weak batteries.
- Trialling in a flat calm only, which hides handling, rig and structural noises.
- Not recording numbers. Impressions fade; temperatures, pressures and rpm on paper are evidence.
- Running too briefly. Cooling problems often appear only after sustained load.
- Ignoring the bilge before and after, which is the easiest way to spot leaks.
- Assuming the gauges are right. Check suspicious readings with an infrared thermometer or a test gauge.
- Treating the trial as optional and signing a sale agreement without a sea trial clause.
Quick checklist
- Sea trial clause in the sale agreement, with deadline.
- Engine cold on arrival; fluid levels, bilge and hour meter recorded.
- Cold start and cooling-water flow checked.
- Readings recorded at each throttle setting.
- Full throttle within about 100 rpm of rated speed.
- Smoke, vibration, noise and smells noted.
- Gear changes and back-down test.
- Shaft seal and rudder gland inspected while running.
- Steering, thrusters and autopilot tested.
- Electronics, charging voltage, lights, pumps and generator checked.
- Sails, winches and rig observed under sail.
- Post-trial bilge, pad, fluids and oil samples.
Sources
Read next
Moisture Readings in a Survey: What the Numbers MeanMost survey reports for fibreglass boats include moisture readings, often presented as a table or a…
What Does a Marine Survey Cover? A Buyer’s ChecklistBuying a boat without a survey is like buying a house without looking in the loft.…
Boat Survey Guide: When You Need One and What to ExpectBuying a used boat without an independent survey is one of the most common and most…
Reader ratings
No ratings yet. Was this useful? Rate it and add what you know: corrections and first-hand tips help the next reader.
★ Rate this guide
Suggest a correction
Cite this page
Sea trial guide: what to check, inspection checklist. Boat Almanac, updated 24 October 2026. https://boatalmanac.com/articles/sea-trial-guide-what-to-check-inspection-checklist/ (accessed 21 November 2026).