Rig and sails
A rig rarely fails without warning, but the warning is small: a broken strand, a cracked swage, a split pin missing, a chainplate weeping rust. Look closely and often, and replace on age as well as on looks.
The rig
- Walk the deck before every passage and look at every fitting: split pins and rings, screws, chainplates, the furler, the gooseneck, the vang.
- Go up the mast (or have it inspected) every season: the masthead fittings, the spreader ends and roots, the sheaves, the lights and the antenna.
- Many insurers and riggers advise replacing stainless standing rigging after about ten to fifteen years whatever it looks like, sooner for a boat that has done a lot of ocean miles; check what your insurer asks.
- Chainplates corrode where you cannot see them, inside the deck: have them pulled and looked at when the rigging is replaced.
- Keep the rig properly tuned: a slack rig loads the fittings in shocks.
Sails
- UV kills sails: a furled sail needs its UV strip, and sails left on the need a cover.
- Check the stitching, the batten pockets, the leech line and the corners every season; a small repair in time saves a sail.
- Reef early: the sail lasts longer and so does the crew.
- Dry sails before storing them; mould and mildew stain and weaken them.
Ocean sailing
- Chafe is the enemy on a long passage: look every day at where sails, sheets and lines rub, and move the wear point.
- Carry a spare and a way to climb the mast at sea.
- Rig a preventer when sailing downwind; an accidental breaks booms and people.
- Have a plan and tools (bolt cutters or a hydraulic cutter) to cut away a broken rig before it holes the boat.
Running rigging, winches and the furler
- Halyards wear where they pass over the sheaves and through the clutches: turn them end for end, or shorten them, before the wear goes through the cover.
- Service the winches every year: strip, clean, grease lightly, check the pawls and springs. A seized pawl lets a loaded sheet run back.
- Furler: the drum and the upper swivel take the load; rinse them with fresh water and check they turn freely. A riding turn on the drum or a halyard wrapped round the top of the foil is the classic furler failure.
- Look at the mast step and the base of the mast: aluminium sitting on steel or in standing water corrodes, and a keel-stepped mast collects water at its foot.
- Spreaders should bisect the angle of the shroud; check the spreader boots and the tips for cracks and chafe.
Seasonal timing
- Northern temperate waters
- Unstep or inspect the mast and send sails for service in the autumn; refit the rig in late winter and tune it after launch.
- Southern temperate waters
- Same, six months later.
- The tropics
- Before the storm season, remove sails and lash or remove what catches wind; inspect and service during the storm season; tune before the first passage.
Tips from experience
- Carry a pair of binoculars on deck to inspect the rig from below.
- Tape over split pins so they do not tear sails.
- Mark the halyards at full hoist and at each reef.
- Keep a rigging and sail inventory with dates.
- Send sails to the loft in the quiet months; the good lofts are busy in spring.
- Wash sails with fresh water now and then and dry them before storing.
- Learn to tune your rig yourself, or have it done after every unstepping.
- Look up every day on passage.
What it usually costs depends on
- Wire or rod, and the boat's size.
- Whether the mast must be unstepped, and the crane.
- Sail cloth and construction.
- The loft's workload (quiet months are better).
Ask for written quotes locally: prices differ a great deal between countries, harbours and seasons.
Common mistakes, and the lesson from each
- ❌ Judging the rigging by its looks alone. Stainless fails from inside. Replace on age, and after many ocean miles.
- ❌ Never going up the mast. The fittings at the top work hardest and are seen least. Look every season.
- ❌ Leaving a furled sail without UV protection. A season of sun can ruin a sail. Keep the UV strip in good repair.
- ❌ Sailing downwind without a preventer. An accidental gybe breaks booms and heads. Rig a preventer.
- ❌ Storing sails wet. Mould weakens and stains. Dry them first.
- ❌ Ignoring chafe on passage. A day of chafe can cut a sheet or a sail. Check daily and move the wear point.
- ❌ Replacing the wire but not looking at the chainplates. Pull and inspect them when you re-rig.
- ❌ No plan to cut away a broken rig. Carry the right cutters and know how to use them.
Go deeper
← The Skipper's Handbook · ‹ Electrics, batteries and power · Below the waterline ›
General guidance from experience, not instructions for your boat: follow the maker's manuals and ask a qualified professional for work you are not sure of.